Ouellet ODB User Manual download pdf

INTERCONNECTION

- The connection boxes and the wiring channel are approved

for interconnection of baseboard heaters and components

which are on the same heating branch circuit.

- For all other options in this series, use ‘‘EMT’’ tubing

or ‘‘BX’’ cable to run wiring.

(Ex: Corner box, empty cabinets, etc.)

- The heater junction box volume without options is

48.2 in.³ (790 cm³).

MAINTENANCE

- Once a year or at the need, remove the front panel and use

a vacuum cleaner to remove the dust accumulation inside

the heater.

- Cleaning should be done while the heater is disconnected

from the main service panel. Wait until the housing and

heating element cool before performing maintenance.

Remove the front panel.

CAUTION: Fins on the element are sharp - Do not touch.

Replace all covers before energizing.

- Any other servicing should be performed by a qualiﬁ ed

technician.

WARRANTY

Ouellet Canada inc. warrants the electric heating element

of the ODB/ODI/ ODBA/ODIA Series for a one (1) year

period; and their component parts against defects in material

and workmanship for a one (1) year period following the

date of purchase, under normal use and service, when proof

of purchase of such is provided to the manufacturer. The

obligation of Ouellet Canada inc., under the terms of this

warranty, will be to supply a new unit and this omits the

manufacturer to bear the installation costs or other secondary

charges linked to replacing the unit or the component part(s).

INS25-200310-03

WIRING DIAGRAM

Double-pole

thermostat

optional

Single-pole

thermostat

optional

Hi-limit

protection

Hi-limit

protection

Element

Double-pole

thermostat

optional

Single-pole

thermostat

optional

180, 3

Avenue, L’Islet (Quebec) G0R 2C0 CANADA

Tel. : (418) 247-3947/1 800 463-7043, Fax : (418) 247-7801

www.ouellet.com

INSTALLATION INSTRUCTIONS

‘‘ODB/ODI/ODBA/ODIA’’ Series

THE INSTALLATION MUST BE EXECUTED

BY A QUALIFIED TECHNICIAN

RISK OF ELECTROCUTION

IMPORTANT INSTRUCTIONS

Basic precautions should always be followed to reduce

the risk of ﬁ re, electric shock, and injury.

- Read all instructions before using this heater.

- A heater has hot and arcing or sparking parts inside.

Do not use in areas where gasoline, paint or ﬂ ammable

liquids are used or stored.

- This heater is hot when in use. To avoid burns, do not let

bare skin touch hot surfaces. Keep combustible materials,

like furniture, pillows, bedding, papers, clothes, and

curtains at least 3 in. (76 mm) from the front of the heater.

- To prevent a possible ﬁ re, do not block air intakes and/or

exhaust in any way whatsoever.

- Do not insert or allow foreign objects to enter any ventilation

or exhaust opening as this may cause an electric shock or

ﬁ re, or damage the heater.

- Do not install heater against combustible low-density

cellulose ﬁ berboard surfaces.

- The heater is not to be located below electrical convenience

receptables.

- WARNING - High temperature: Keep electrical cords, drapes,

and other furnishings away from heater.

- Use only with copper branch circuit conductors.

- For bathroom use, the heater must be installed so that

switches and other controls cannot be touched by anyone

in the bath or shower.

- To avoid possible electrical shock, disconnect all power

at the main panel prior to wiring, cleaning, or servicing.

- Do not use outdoors.

- CAUTION: Hazard of electric shock - With the option

‘‘electrical convinience receptable’’ mounted in a standard

heater - More than one disconnect switch may be required to

de-energize the equipment for servicing.

- Use this heater only as described in this manual. Any other

use not recommended by the manufacturer may cause ﬁ re,

electric shock, or injury.

KEEP THESE INSTRUCTIONS

INSTALLATION / USER

With the option ‘‘Bottom fresh air inlet’’, install bottom of

heater not less than 2 in. (50 mm) above ﬁ nished ﬂ oor.

1- Remove baseboard front panel by removing screws at

bottom and remove the appropriate junction box cover.

2- Remove required knockouts.

3- Install the relay or thermostat if supplied as a kit.

See Options section for details.

4- Make electrical connection according to the wiring diagram

in accordance with local and national codes.

5- Secure heater to the wall and loose screws by 1/2 turn for

metal thermal expansion.

6- Replace junction box cover and baseboard front panel

before energizing.

OPTIONS

All heating equipment and options must be installed in

accordance with local and national codes.

Built-in thermostat:

- Refer to the upper wiring diagram for connections.

- Refer to instructions supplied with this option for mounting.

Built-in relay:

- Refer to the diagram included with the relay option

for connections

- Refer to instructions supplied with this option for mounting.

CORNERS AND BLANK SECTIONS

- Install blank sections and corners same way as heating unit

of this series.

- Install corners using the mounting holes.

- Use ‘‘EMT’’ tubing or ‘‘BX’’ cable to run wiring into

these options.

Summary of Contents

Page 1 - KEEP THESE INSTRUCTIONS

INTERCONNECTION- The connection boxes and the wiring channel are approved for interconnection of baseboard heaters and components which are on th

Ouellet ODB User Manual

Browse online or download User Manual for Water boiler Ouellet ODB. Ouellet ODB User Manual

Summary of Contents

Related models: ODBA | ODI | ODIA |

More documents for Water boiler Ouellet ODB

Comments to this Manuals

Ouellet ODB User Manual

Browse online or download User Manual for Water boiler Ouellet ODB. Ouellet ODB User Manual

Summary of Contents

Related models: ODBA | ODI | ODIA |

More documents for Water boiler Ouellet ODB

Comments to this Manuals

Related products and manuals for Water boiler Ouellet ODB